# Simulation Error: 'STOP NONSENSE GAS' for High-Density Deuteride Compounds

**URL:** <https://fluka-forum.web.cern.ch/t/simulation-error-stop-nonsense-gas-for-high-density-deuteride-compounds/6626>\
**Category:** Geometry and Materials\
**Created:** [28 October 2024 20:56 UTC](https://fluka-forum.web.cern.ch/t/simulation-error-stop-nonsense-gas-for-high-density-deuteride-compounds/6626 "2024-10-28T20:56:21Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![federico.galli](https://fluka-forum.web.cern.ch/letter_avatar_proxy/v4/letter/f/e56c9b/32.png) [@federico.galli](https://fluka-forum.web.cern.ch/u/federico.galli)\
**Post date:** [28 October 2024 20:56 UTC](https://fluka-forum.web.cern.ch/t/simulation-error-stop-nonsense-gas-for-high-density-deuteride-compounds/6626/1 "2024-10-28T20:56:21Z")

</div>

Good morning everyone,

I need your help with a specific issue. When I set the density of my deuteride compound (for example, titanium deuteride), and it exceeds a certain critical value (around 70 g/cm³ for titanium deuteride), the simulation immediately stops, displaying the error: “Abort called from DPDX reason NONSENSE GAS Run stopped! STOP NONSENSE GAS.” This critical value varies from case to case—for instance, the error occurs at densities close to 1300 g/cm³ for a UD4 compound and at around 1 g/cm³ for a simpler deuterium-only target.

I have read about this type of error on the FLUKA Forum, but I would like to understand more specifically why it occurs in my case. I have attached the .flair and .inp files for reference.

Thank you all in advance for your assistance.  
[High-density D.flair](https://fluka-forum.web.cern.ch/uploads/short-url/1zvFMhE4phnKFupvCBqLW7HYakC.flair) (3.1 KB)  
[High-density D.inp](https://fluka-forum.web.cern.ch/uploads/short-url/2WBTAMa9fCDDL9PmC4ZgFcBuoYY.inp) (2.3 KB)

---

<div class="post-metadata">

**Author:** ![rmartin](https://fluka-forum.web.cern.ch/letter_avatar_proxy/v4/letter/r/7c8e57/32.png) [@rmartin](https://fluka-forum.web.cern.ch/u/rmartin)\
**Post date:** [1 November 2024 17:34 UTC](https://fluka-forum.web.cern.ch/t/simulation-error-stop-nonsense-gas-for-high-density-deuteride-compounds/6626/2 "2024-11-01T17:34:25Z")

</div>

Hi Federico,

I am not too familiar with the internals of FLUKA, but these densities look like some extreme states of matter that can’t exist at atmospheric pressure. Even if they might not technically be gasses, I managed to make the WD2 job run through by setting the “gas” pressure to (arbitrary) 13000 atmospheres via the [MAT-PROP](https://flukafiles.web.cern.ch/manual/chapters/description_input/description_options/mat-prop.html) card. So you should calculate to correct pressure for each material and set it accordingly. I do not know if the results will be physical though.

Cheers,  
Roman

---

<div class="post-metadata">

**Author:** ![federico.galli](https://fluka-forum.web.cern.ch/letter_avatar_proxy/v4/letter/f/e56c9b/32.png) [@federico.galli](https://fluka-forum.web.cern.ch/u/federico.galli)\
**Post date:** [5 November 2024 11:24 UTC](https://fluka-forum.web.cern.ch/t/simulation-error-stop-nonsense-gas-for-high-density-deuteride-compounds/6626/3 "2024-11-05T11:24:12Z")

</div>

Hi Roman,

Thank you very much for your assistance. You have resolved my problem.

Cheers,  
Federico

---

<div class="post-metadata">

**Author:** ![rversaci](https://fluka-forum.web.cern.ch/letter_avatar_proxy/v4/letter/r/cc9497/32.png) [@rversaci](https://fluka-forum.web.cern.ch/u/rversaci)\
**Post date:** [13 November 2024 07:21 UTC](https://fluka-forum.web.cern.ch/t/simulation-error-stop-nonsense-gas-for-high-density-deuteride-compounds/6626/4 "2024-11-13T07:21:19Z")

</div>

Closed on 13 November 2024 07:21 UTC


