# Some physical issues in simulation

**URL:** <https://fluka-forum.web.cern.ch/t/some-physical-issues-in-simulation/5090>\
**Category:** Scoring\
**Created:** [6 September 2023 13:58 UTC](https://fluka-forum.web.cern.ch/t/some-physical-issues-in-simulation/5090 "2023-09-06T13:58:12Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![ZhongLy](https://fluka-forum.web.cern.ch/letter_avatar_proxy/v4/letter/z/8edcca/32.png) [@ZhongLy](https://fluka-forum.web.cern.ch/u/ZhongLy)\
**Post date:** [6 September 2023 13:58 UTC](https://fluka-forum.web.cern.ch/t/some-physical-issues-in-simulation/5090/1 "2023-09-06T13:58:13Z")

</div>

Dear expert,

Continuing the discussion from [How to record the energy spectrum of triton?](https://fluka-forum.web.cern.ch/t/how-to-record-the-energy-spectrum-of-triton/5004):

Thanks for your clear guidance! But the parameter ‘Ekin frac’ in LOW-PWXS still confuse me.

I change it from 0.0001 to 0.1(Figure 1 -4), and I observed a marked difference. How do I decide which is the most suitable?

 ![1](https://fluka-forum.web.cern.ch/uploads/default/original/2X/e/e21578aee3bbd8cca14ff699a69b89bb5d1412d7.png)  
 ![2](https://fluka-forum.web.cern.ch/uploads/default/original/2X/f/fddab77136b9dac8d9ce71d6eee6ae3b82cbb2b6.png)  
 ![3](https://fluka-forum.web.cern.ch/uploads/default/original/2X/7/706136637d1cd9a9ad535b46e17df4656fcab56e.png)  
 ![4](https://fluka-forum.web.cern.ch/uploads/default/original/2X/7/733212da32b5d29cb2642cda420d3c1ca077b2c4.png)

In addition, the literature shows the energies of particulate emissions are 2.05 and 2.75MeV. Why is it different from the simulation result?

Thanks in advance！

---

<div class="post-metadata">

**Author:** ![sniang](https://fluka-forum.web.cern.ch/letter_avatar_proxy/v4/letter/s/8797f3/32.png) [@sniang](https://fluka-forum.web.cern.ch/u/sniang)\
**Post date:** [21 September 2023 15:09 UTC](https://fluka-forum.web.cern.ch/t/some-physical-issues-in-simulation/5090/3 "2023-09-21T15:09:04Z")

</div>

Hello @ZhongLy,

Once again, sorry for the delay.  
The Ekin frac is not a parameter of LOW-PWXS but of FLUKAFIX card.

The oscillations you observe are artifacts resulting from excessively long steps. Using FLUKAFIX will address the issue by reducing the step size, thereby increasing precision. I suggest that you decrease the steps until these oscillations are eliminated.

0.0001 appears to be an appropriate value for your situation.

All the best,  
Samuel

---

<div class="post-metadata">

**Author:** ![rversaci](https://fluka-forum.web.cern.ch/letter_avatar_proxy/v4/letter/r/cc9497/32.png) [@rversaci](https://fluka-forum.web.cern.ch/u/rversaci)\
**Post date:** [5 October 2023 06:01 UTC](https://fluka-forum.web.cern.ch/t/some-physical-issues-in-simulation/5090/4 "2023-10-05T06:01:16Z")

</div>


